Swimming Pool Repairs in DFW take a beating. Between the brutal summers, unpredictable freezes, and naturally hard water, there’s always something that needs attention. Here are the repairs we see most often:
Common Swimming Pool Repairs in North Texas
Pump and Motor Failures
This is the number one call we get. Motors burn out from running in extreme heat, bearings wear down, capacitors fail. Sometimes the pump housing itself cracks from freeze damage. Repair costs typically range from $250 to $800 for common fixes, while a full pump replacement with installation runs $600 to $1,200 or more if you’re upgrading to variable-speed.
Filter System Issues (Sand, Cartridge, DE)
Filters don’t last forever. Sand media wears out and stops catching fine particles. Cartridge filters get clogged beyond what cleaning can fix. DE filter grids tear or crack. When your filter isn’t doing its job, your water turns cloudy and your pump has to work overtime to compensate. Expect to pay anywhere from $75 to $800 depending on the filter type and whether it needs a repair or full replacement.
Heater and Heat Pump Malfunctions
If your pool heater is throwing error codes, cycling on and off, or just not warming the water like it used to, something’s going on internally. Gas heater repairs run $150 to $1,200 depending on the issue — anything from a thermostat swap to heat exchanger work. Electric heat pumps are usually simpler to fix, typically $200 to $800. Either way, heaters mix gas, electricity, and water, so this one’s best left to a licensed pro.
Pool Light Replacement
A burned-out pool light seems minor, but remember — you’re dealing with electricity and water. A basic bulb and gasket replacement might cost $65 to $150, but if the entire fixture needs replacing, LED upgrades can run $700 to $1,500 per light. This is absolutely not a DIY job. Improper pool light work creates serious safety hazards.
Plumbing Leaks and Cracked Pipes
Plumbing issues are sneaky. You might notice your water level dropping faster than normal, soggy spots in the yard near the pool, or air bubbles in the return lines. In North Texas, freeze damage is the biggest cause of cracked underground pipes and busted fittings. Leak detection alone costs $250 to $400, and the actual repair can range from $200 to $1,000 depending on where the break is and how much digging is involved.
Surface Cracks and Staining
Over time, pool plaster develops cracks and stains from chemical exposure, our hard North Texas water, and just general age. Small cracks can be patched, but once the surface starts peeling or becoming rough to the touch, resurfacing is usually the move. That’s a bigger project, but catching surface issues early keeps the repair costs manageable.
How to Tell If Your Pool Needs Professional Repair
Some things are obvious — a pump that won’t turn on, water gushing from a pipe. But a lot of pool problems start subtly. If your water is consistently cloudy even after chemical adjustments, your electric bill spikes without explanation, the pool loses more than a quarter inch of water per day, or you hear unusual sounds from any equipment — those are all signs that something needs professional eyes. The longer you wait, the worse it gets and the more expensive the fix becomes. Don’t sit on warning signs.
Swimming Pool Repair Costs in the DFW Metroplex
To give you a quick snapshot: pump repairs run $250 to $800, heater fixes $150 to $1,200, filter work $75 to $800, light replacements $65 to $1,700, plumbing repairs $200 to $1,000, and leak detection $250 to $400. These are all DFW-area averages that account for labor, parts, and the general complexity of each job. Labor rates from professional pool techs in Texas typically fall between $75 and $150 per hour.
As for insurance — standard homeowner’s policies usually don’t cover normal wear and tear or maintenance-related failures. But if your pool equipment was damaged by a specific event like a storm or a freeze that’s covered under your policy, you may have a claim. It’s always worth checking with your insurance agent, especially after a major weather event.
Freeze Damage Pool Repair
If you’ve lived through a DFW winter, you know the drill. Temps drop below freezing, sometimes for days at a stretch, and pools that weren’t properly prepared pay the price. Water trapped in pump housings expands and cracks the plastic. PVC pipe connections split. Heater internals get damaged. Freeze guards help, but they’re not foolproof — especially during extended freezes where the power goes out.
We see the heaviest wave of freeze-related repair calls every January and February. If your pool wasn’t winterized before a cold snap, the smartest thing you can do is have a technician inspect everything before you try turning the system back on. Running a pump with cracked plumbing or a damaged housing just makes things worse.
Choosing a Reliable Pool Repair Company in North Texas
Check for Licensing and Insurance
In Texas, technicians working on pool equipment with high-voltage electricity need to be licensed through the Texas Department of Licensing and Regulation. Ask for proof. And make sure they carry liability insurance. If something goes wrong during a repair and the company isn’t insured, that’s your problem.
Ask About Warranties on Repair Work
A company that stands behind its work will offer some kind of warranty — whether that’s 90 days on labor, a year on parts, or both. If they won’t guarantee the repair at all, that tells you something about how confident they are in their own technicians.
Read Local Reviews and Get Multiple Quotes
Check Google reviews, look at their Facebook page, ask around in your neighborhood. In cities like Frisco, Plano, and McKinney, people talk. And don’t just go with the first quote you get. Comparing two or three estimates helps you understand whether you’re getting a fair deal and gives you a sense of how each company communicates.
People Also Ask
How long does a pool repair take?
It really depends on the job. A pump seal replacement or capacitor swap can be done in under an hour. A motor replacement takes a couple hours. Plumbing leak repairs that require digging can stretch to a full day or more. Bigger projects like resurfacing take one to three weeks. Your repair company should give you a clear timeline before work begins.
Can I use my pool while it’s being repaired?
It depends on what’s being fixed. If the pump or filter is being worked on, you should stay out — there’s no circulation to keep the water safe, and there may be electrical work happening. For things like tile repairs or minor surface patches, your tech will let you know whether the pool needs to be off-limits and for how long.
What pool repairs should I not attempt myself?
Anything electrical — full stop. That includes motor work, light fixtures, heater wiring, and automation systems. Plumbing that involves cutting and gluing PVC under pressure is risky too if you don’t have experience. And gas heater repairs? Never. The risk of a gas leak or improper venting is too serious. Stick to the simple stuff like cleaning baskets and checking water levels, and call a pro for everything else.
PoolBurg’s Swimming Pool Repair Services Across DFW
PoolBurg handles the full range of pool repairs — pumps, motors, heaters, filters, lights, plumbing, and more. We diagnose first and explain everything before we pick up a wrench. No surprise charges, no unnecessary upsells. We serve Frisco, Plano, McKinney, Allen, Prosper, The Colony, Little Elm, Celina, Garland, and the rest of our 17-city North Texas service area. Every repair comes with honest pricing and clear communication from start to finish.
Something off with your pool? Let’s figure it out.
Request a repair estimate — no obligation, no pressure.
Visit poolburg.com or call us today.
