What does a pool tech do for those forty-five minutes they’re in your backyard? It’s a question I get a lot, and frankly, it’s a fair one. I’ve been in the North Texas pool industry for over 35 years, and I’ve seen it all—from the “drive-by” service where a guy throws in a tab and leaves in ten minutes, to the true professionals who treat your pool like it’s their own.
At PoolBurg, we don’t believe in secrets. If you’re paying for a professional to maintain your investment, you should know exactly what you’re getting. This guide is our open-book pool service checklist, detailing every test, every brush stroke, and every equipment check we perform to keep your Frisco or Southlake pool crystal clear. This is the level of care you should what to expect from pool service every single time.
Total Transparency — Here’s Exactly What Happens at Every PoolBurg Service Visit
Many homeowners hire a service and have no idea what’s actually happening behind the gate. Some companies rush through visits because they have too many stops on their route. To us, that’s not service; that’s a liability. A properly maintained pool requires a systematic approach. According to PHTA, consistent water quality management is the only way to prevent structural damage and health risks.
Water Chemistry Testing and Balancing (10-15 minutes)
The first thing we do is assess the “health” of your water. This isn’t just about making it look blue; it’s about science.
- Free Chlorine: We target 2-4 ppm. In the 100°F Texas sun, chlorine burns off faster than anywhere else in the country.
- pH Levels: We aim for 7.2-7.6. Because North Texas water is naturally “hard,” your pH will almost always drift high. We add muriatic acid at nearly every visit to keep things balanced.
- Alkalinity: This is your pH “anchor.” We keep it at 80-120 ppm to prevent those wild chemical swings.
- Chemical Adjustments: We only use professional-grade liquid chlorine (which adds zero CYA or extra calcium) and high-potency acid. The CDC emphasize that proper sanitizer levels are the first line of defense against waterborne illnesses.
Pool Cleaning (15-25 minutes)
Once the chemistry is set, we move to the physical work.
- Skimming & Brushing: We remove every leaf and bug from the surface. Then, we brush the walls and floor. For gunite pools, this is vital; algae loves to hide in the porous plaster.
- Waterline Scrubbing: We give special attention to the tile line. This prevents the white calcium “scale” that DFW’s hard water loves to leave behind.
- Vacuuming: We manually vacuum the floor to pick up what the brush loosened. If things are really messy, we vacuum to “waste” to keep that junk out of your filter.
Filter Maintenance (5-10 minutes)
Your filter is the kidney of your pool. If it’s clogged, the water stops moving, and the algae starts growing. We check your pressure gauge against a “clean baseline.” If it’s 8-10 PSI high, we backwash your sand or DE filter immediately. We also check the WQA on mineral buildup, which reminds us that in North Texas, filters work twice as hard to catch calcium particles.
Equipment Inspection (5-10 minutes)
This is where the 35+ years of experience really comes in. We don’t just look; we listen.
- Pump & Motor: We listen for bearrings whining or air leaks.
- Electrical & Safety: We test your GFCI at every visit. Per the NEC 2026 electrical codes, all pool equipment must have functioning ground-fault protection to prevent accidents.
- VGB Compliance: We verify your drain covers are intact and meet the(https://www.c-m-p.com/vgb-drain-check-safety-checklist/) to prevent entrapment hazards.
After-Service Report
When we’re done, we don’t just vanish. You’ll receive a digital report sent straight to your phone. It includes your chemical readings (before and after), the work we did, and photos of any equipment issues we spotted. If your water is looking a bit dull, we might suggest an acid wash or a filter deep clean.
People Also Ask
What does a pool service visit include?
It should include a full water chemistry analysis, balancing, skimming, brushing, vacuuming, and a complete equipment safety check.
How long should a pool service visit take?
For a standard pool, you should expect us on-site for 35 to 50 minutes. If a tech is gone in 15, they aren’t doing the full checklist.
How do I know if my pool service is doing a good job?
Check your waterline for scale and your corners for “mustard” algae. If those are clean and you’re getting a detailed weekly report, you’re in good hands.
PoolBurg — Now You Know Exactly What You’re Getting
We believe that when you know what does a pool tech do, you appreciate the value of professional service even more. We’re not just cleaners; we’re the guardians of your backyard paradise. Want to see exactly what professional pool service looks like? Schedule your first PoolBurg visit — free assessment included.
